Abstract
The issue of growing demand on our nation’s roadways over that past couple of decades, decreasing budgetary funds, and the need to
provide a safe, efficient, and cost effective roadway system has led to a dramatic increase in the need to rehabilitate our existing
pavements and the issue of building sustainable road infrastructure in India. With these emergency of the mentioned needs and this
are today’s burning issue and has become the purpose of the study.
In the present study, the samples of existing bituminous layer materials were collected from NH-48(Devahalli to Hassan) site.The
mixtures were designed by Marshall Method as per Asphalt institute (MS-II) at 20% and 30% Reclaimed Asphalt Pavement (RAP).
RAP material was blended with virgin aggregate such that all specimens tested for the, Dense Bituminous Macadam-II (DBM-II)
gradation as per Ministry of Roads, Transport, and Highways (MoRT&H) and cost analysis were carried out to know the economics.
Laboratory results and analysis showed the use of recycled materials showed significant variability in Marshall Stability, and the
variability increased with the increase in RAP content. The saving can be realized from utilization of recycled materials as per the
methodology, the reduction in the total cost is 19%, 30%, comparing with the virgin mixes.
Keywords: Reclaimed Asphalt Pavement, Marshall Stability, MS-II, Dense Bituminous Macadam-II
Guardians and Glitches: Navigating the Duality of Gen AI in AppSec
Laboratory studies of dense bituminous mixes ii with reclaimed asphalt materials
1. IJRET: International Journal of Research in Engineering and Technology eISSN: 2319-1163 | pISSN: 2321-7308
__________________________________________________________________________________________
IC-RICE Conference Issue | Nov-2013, Available @ http://www.ijret.org 239
LABORATORY STUDIES OF DENSE BITUMINOUS MIXES-II WITH
RECLAIMED ASPHALT MATERIALS
C.Udayshankar1
, M.Varuna2
1
M.Tech student, 2
Assistant professor, Department of civil engineering, R.V. college of Engineering,
Bangalore-560059, India
c.udayshankars@gmail.com, varun.m07@gmail.com
Abstract
The issue of growing demand on our nation’s roadways over that past couple of decades, decreasing budgetary funds, and the need to
provide a safe, efficient, and cost effective roadway system has led to a dramatic increase in the need to rehabilitate our existing
pavements and the issue of building sustainable road infrastructure in India. With these emergency of the mentioned needs and this
are today’s burning issue and has become the purpose of the study.
In the present study, the samples of existing bituminous layer materials were collected from NH-48(Devahalli to Hassan) site.The
mixtures were designed by Marshall Method as per Asphalt institute (MS-II) at 20% and 30% Reclaimed Asphalt Pavement (RAP).
RAP material was blended with virgin aggregate such that all specimens tested for the, Dense Bituminous Macadam-II (DBM-II)
gradation as per Ministry of Roads, Transport, and Highways (MoRT&H) and cost analysis were carried out to know the economics.
Laboratory results and analysis showed the use of recycled materials showed significant variability in Marshall Stability, and the
variability increased with the increase in RAP content. The saving can be realized from utilization of recycled materials as per the
methodology, the reduction in the total cost is 19%, 30%, comparing with the virgin mixes.
Keywords: Reclaimed Asphalt Pavement, Marshall Stability, MS-II, Dense Bituminous Macadam-II
--------------------------------------------------------------------***-----------------------------------------------------------------------
1. INTRODUCTION
Road Transport in India accounts for 80% of passenger
movement and 65% of freight movement. With 3.34 million
km of roads, India has the second largest road network in the
world. The current state of our nation’s transportation
infrastructure is inadequate, and many state and city
municipalities do not have the funds to rehabilitate their road
networks to improve them to an acceptable level. National
Highways Authority of India has prepared plans involving an
outlay of Rs 2, 20,000 crores under National Highways
Development Program (NHDP) and 10,000 km of
expressways at a cost of Rs 1, 00,000 crores are being
planned.
The eleventh plan investment in roads and bridges is about Rs
2, 78,658 crores which is about 13.57 % of total outlay. These
mega road modernization projects throws up various
concerns pertaining to depletion of resources like good soil
and aggregates, long lead to get good quality aggregates and
increase in fuel consumption etc,. Furthermore, the supply of
Bitumen, whose cost keeps on increasing, is dependent on
foreign sources, and energy that is needed for processing new
materials is becoming costlier every day. Therefore recycling
of existing bituminous mixes results in substantial savings
through the reuse of aggregates and bitumen. Recycling of
asphalt pavements is a technology developed to rehabilitate
and/or replace pavement structures suffering from permanent
deformation and evident structural damage [3].
Use of the recycled materials in the road construction has been
favored over virgin materials in the light of increasing cost of
bitumen, scarcity of good quality aggregates and the priority
towards preservation of the environment. Considering the
material and construction cost alone, it is estimated that using
recycled materials, saving ranging from 14 to 34% can be
achieved [2].
1.1 Objectives
The main objective of the research is to evaluate the effects of
partial replacement of aggregates by RAP on the properties of
dense bituminous macadam, Grade-II are
1. To determine the basic engineering properties of the
Virgin bitumen and Virgin aggregate and the basic
engineering properties of Reclaimed Aggregate and
binder after extraction and Recovery.
2. To carry out the blending of RAP and Virgin
aggregates for 20% and 30% RAP content as per
Asphalt Institute (MS-II), according DBM-II gradation
as per MoRT&H(4th
revision).
2. IJRET: International Journal of Research in Engineering and Technology eISSN: 2319-1163 | pISSN: 2321-7308
__________________________________________________________________________________________
IC-RICE Conference Issue | Nov-2013, Available @ http://www.ijret.org 240
3. To carry out the mix design for 20% and 30% recycled
mixes with virgin mixes as per Asphalt Institute (MS-
II) and compared with Marshall Properties.
4. To workout the economics of recycling of bituminous
pavement materials, comparing with conventional
virgin mixes.
2. EXPERIMENTAL INVESTIGATION
Representative samples of 200 kg milled RAP was collected
from the NH-48(Devahalli to Hassan stretch) for further
investigation. The RAP materials were subjected to solvent
(benzene) extraction method by centrifuge extractor and the
average bitumen content were found to be 3.2%.Furtherly,
sieve analysis was carried out on the extracted aggregates. It
was found that the aggregate lies in the band of specified
limits for dense bitumen macadam grade-II as per MoRT&H,
(4th
revision). The solvent obtained after the extraction taken
for distillation to recover the binder for further studies.
2.1 Evaluation of binder in RAP:
The binder extracted from RAP was tested for its penetration
value and it was found to be 19mm, which satisfies the
minimum criteria of 15mm.
Furtherly the same evaluated after rejuvenation using virgin
60/70 binder and found to be 48mm which also satisfies the
minimum criteria as per MoRT&H, Clause 517.2.6.
2.2 Virgin and Recycled Aggregate Properties:
The aggregate properties were measured from the extracted
sample (Table-1) and tested for its suitability. Recycled
aggregate were found to satisfy the requirements as per
MoRT&H.
Table-1 properties of recycled and virgin aggregates
Properties Virgin RAP Permissible Limit
Impact value(AIV),% 19.62 17.12 27 max.
Crushing value,% 22.7 - 24 max.
Abrasion value,% 21.5 - 35 max.
Specific Gravity,% 2.65 2.7 2 .5-3.0
Combined index,% 24.30 26 30 max.
2.3 Virgin Bitumen Properties:
For the study, Bitumen 60/70 grade was considered and their
properties were tested for its suitability for the study (Table-2).
The bitumen properties were found to satisfy the requirements
Table-2 Properties of Virgin Binder (60/70)
Properties 60/70
Permissible
Limit
Specification
Penetration at 25°c,5sec
64 60-70 IS -1203:1978
Softening point(R&B),°C 49 45-55 IS -1205:1978
Flash point, °C 295 175 min. IS -1448:1969
Ductility at 25°C,cm 82 75 min. IS -1208:1978
Specific gravity 1.01 0.99 min. IS -1202:1978
Viscosity-60ºC,poise,0.3 RPM 1730 1000 min. ASTM-D 4402
Viscosity-135ºC,poise,100 RPM 3.6 - ASTM-D 4402
After RTFO, Loss in weight, % 0.40 1 max. -
Reduction in Penetration of residue at 25°c,% 10.93 48 max. -
Increase in Softening point, °c 1.27 - -
3. IJRET: International Journal of Research in Engineering and Technology eISSN: 2319-1163 | pISSN: 2321-7308
__________________________________________________________________________________________
IC-RICE Conference Issue | Nov-2013, Available @ http://www.ijret.org 241
3. MIX DESIGN:
The mix design was carried out for virgin aggregate as well as
for the blended mixture of various ratio of RAP to fresh
materials viz., 20:80, and 30:70. The details of RAP gradation
and the quantity of fresh aggregates required in accordance
with MS-II are summarized in Table-3.
Table-3 Percentage of virgin and RAP aggregates
Sl.
No
IS sieve
Desired %
for DBM
mix
% available
in RAP
Material
% Available of
RAP material
Balance 80 % of
Virgin Aggregate
% Available
of RAP
material
Balance 70 %
of Virgin
Aggregate
20% 30%
1 37.5-26.5 5 0 0 5 0 5
2 26.5-19 12 2.9 0.58 11.42 0.87 11.13
3 19-13.2 15 6.8 1.36 13.64 2.04 12.96
4 13.2-4.75 22 46.25 9.25 12.75 13.875 8.125
5 4.75-2.36 11 14.8 2.96 8.04 4.44 6.56
6 2.36-0.3 21 17.45 3.49 17.51 5.235 15.765
7 0.3-0.075 9 5.5 1.1 7.9 1.65 7.35
8 Below 0.075 5 2.8 0.56 4.44 0.84 4.16
total 19.3 80.7 28.95 71.05
3.1 Actual Percentage of Virgin Binder:
The bitumen percentages to be added for preparation of trail
mixes are calculated as per MS-II, considering the existing
bitumen content in RAP materials. Marshall Properties: Table-
4 shows the stability and volumetric properties obtained for 20
and 30% and Virgin mixes.
Table-4 Properties of Recycled and Virgin mixes
Properties tested
Recycled mixes
Virgin mixes
Criteria as per
MoRT&H
20% 30%
OBC,% 4.37 4.1 4.63 ----
Stability, Kn 23.09 25.43 21.76 9Kn min
Flow, mm 3.3 3.36 3.48 2-4
Air voids,% 5 3.97 4.74 3-6
Unit weight 2.37 2.4 3.54 -----
VMA,% 19.73 18.18 18.14 12.5min
VFB,% 74.59 78.1 73.84 65-75
The Figure-1 represents the variation in various Marshall
Properties for different percentage of RAP mixes.
4. IJRET: International Journal of Research in Engineering and Technology eISSN: 2319-1163 | pISSN: 2321-7308
__________________________________________________________________________________________
IC-RICE Conference Issue | Nov-2013, Available @ http://www.ijret.org 242
Fig 1 Variation of Marshall Properties
The Figure-2 shows the variation in the stability for various
RAP mixes of 0, 20, and 30% with respect to bitumen content.
Fig 2 Variation of Stability with respect to bitumen content
4. ECONOMIC ANALYSIS
A typical example for one kilometer length for two lane
highway, width of 7m, and depth of 0.1m were considered for
cost analysis, additionally milling is considered in case of
RAP. The costs are calculated based on the schedule of rates
of Govt. of Karnataka. The details of economic analysis are
shown in Table-5.
Table-5 Economic analysis
Particulars Total Quantity(cum) Amount(Rs)
Virgin 733 57,43,788
20% RAP 586 46,24,621
30% RAP 513 40,52,593
CONCLUSIONS
Based on the experimental result and after analyzing the
results, the following may be concluded.
1. DBM-II mixes prepared with RAP materials 20%,
30% shows higher stability of when compared with
the conventional virgin mixes and other Marshall
properties are within the specified limits.
2. The saving can be realized from utilization of
recycled materials as per the methodology, the
reduction in the total cost is 19%, 30%comparing
with the virgin mixes.
0
5
10
15
20
25
30
0 10 20 30
Stability(Kn)
RAP content (%)
4
4.1
4.2
4.3
4.4
4.5
4.6
4.7
0 10 20 30
OBC(%)
RAP CONTENT (%)
0
1
2
3
4
5
6
0 10 20 30 40
Airvoids
RAP content (%)
0
1
2
3
4
0 10 20 30 40
BulkDensity(gm/cc)
RAP content (%)
1500
1700
1900
2100
2300
2500
2700
2900
3 4 5 6
Stability(Kg)
% of Bitumen content
Virgin
20% RAP
30% RAP
5. IJRET: International Journal of Research in Engineering and Technology eISSN: 2319-1163 | pISSN: 2321-7308
__________________________________________________________________________________________
IC-RICE Conference Issue | Nov-2013, Available @ http://www.ijret.org 243
REFERENCES
[1] Report for Mission Group on Infrastructure
Development, Planning Department, Government of
Karnataka, September 2010, Pg-1-8.
[2] Kanishak chopra, anjan kumar, Rajib basu mallick and
Veeraragavan, “Investigation on laboratory
performance of bituminous mixes with reclaimed
asphalt pavement materials-a step towards sustainable
road infrastructure in India”, Journal of Indian road
congress, Paper no. 584, December 2012, Pg-339-352.
[3] Valdes, G., Perez-Jimenez, F., Miro, R., Martinez, A.,
& Botella, R “Experimental study of recycled asphalt
mixtures with high percentages of reclaimed asphalt
pavement (RAP)”. Construction and Building
Materials, 25(3),2011,Pg- 1289 – 1297
[4] K. Aravind, Animesh Das, “Pavement design with
central plant hot-mix recycled asphalt mixes”,
Construction and Building Materials journals - Indian
Institute of Technology Kanpur, July 2006, Pg-928-936.